1970 Buick LeSabre Ignition Distributor

Part Number: 13715-09147862

Notes: Distributor -- with 14 Tooth Gear; Point Type

Features:

• 100% new points and condensers installed where applicable
• All electronic module components are 100% computer tested to ensure full functionality
• Automated test equipment verifies signal strength, correct polarity of wire harness, air gap, crank reluctor tooth size, as well as ignition coil and pickup performance
• Guaranteed fit and function
• Meets or exceeds O.E.M. performance
• O.E. components with consistently high failure rates are 100% replaced or repaired to meet or exceed O.E. performance
• Precise machining tolerances prevent oil leakage, poor timing, setting of the "Check Engine" light, and premature failure
• Remanufactured under stringent quality standards to ensure product reliability
• Show More
• Show Less

Part Number: 13715-07386302

Notes: Max Fire Distributor -- Three Wire Hook-Up; Centerless Ground Shaft; High Output Magnetic Pickup; Large Paddle Wheel Reluctor; CARB E.O. For Use On Pre-Pollution Controlled Vehicles

Features:

• CNC Machined From 6061-T6 Alum. w/O-Ring Grooves
• Stainless Steel Rotor Spring For Max. Conductivity
• For Use in Fully Machined Engine Block
• Hardened Iron Drive Gear Ensures Long Service Life
• Cap And Rotor Are Molded In 30 Percent Glass Filled Polyester
• Adj. Mechanical And Vacuum Adv. For Increased Mileage Potential
• Features Brass Contacts

Part Number: 13715-09003282

Notes: Distributor -- with 13 Tooth Gear; Point Type

Features:

• 100% new points and condensers installed where applicable
• All electronic module components are 100% computer tested to ensure full functionality
• Automated test equipment verifies signal strength, correct polarity of wire harness, air gap, crank reluctor tooth size, as well as ignition coil and pickup performance
• Guaranteed fit and function
• Meets or exceeds O.E.M. performance
• O.E. components with consistently high failure rates are 100% replaced or repaired to meet or exceed O.E. performance
• Precise machining tolerances prevent oil leakage, poor timing, setting of the "Check Engine" light, and premature failure
• Remanufactured under stringent quality standards to ensure product reliability
• Show More
• Show Less

Part Number: 13715-07738923

Notes: Billet Distributor -- Incl. Cap / Race Rotor; Use With MSD 6 / 7 / 8 / 10 Series Ignition; Without Vacuum Advance; Iron Gear; Legal On Non-Emissions Controlled Vehicles Or For Race Use

Features:

• Advance plate and weights are fine blanked from chrome moly steel
• No CARB Exemption Order Number
• Must Be Used w/An MSD Ignition Control
• QPQ coated for friction reduction
• Supplied w/HEI style distributor cap/rotor (accepts Cap-A-Dapts)
• QPQ coated polished steel shaft; guided by sealed ball bearings
• Mech. advance assem. can be locked out for crank trigger systems
• Easy-to-adjust mech. advance w/supplied springs and stop bushings
• CNC machined billet aluminum housing and billet aluminum base

Part Number: 13715-03142101

Notes: Ready-To-Run Distributor -- Iron Gear; CARB E.O. D-40-39

Features:

• Vacuum advance canister for improved economy (can be locked out)
• CARB E.O. Approved
• QPQ coated polished steel shaft; guided by sealed ball bearings
• Easy-to-adjust mech. advance w/supplied springs and stop bushings
• Does not require an MSD Ignition Control
• Maintenance-free magnetic pickup and precision reluctor
• Built-in module produces a 7.5 amp single spark through high rpm
• Supplied w/HEI style distributor cap/rotor (accepts Cap-A-Dapts)
• Creates stable trigger signals throughout the rpm range
• Simple and clean three wire installation
• Includes built-in Rev Limiter
• Mech. advance assem. can be locked out for crank trigger systems